SMOK NFIX PRO Empty Pod In UAE

Get SMOK Nfix Pro Empty Pod Cartridge in UAE — 3 Pack, 2ml

SMOK Nfix Pro Empty Pod Cartridge is a 2ml refillable replacement pod that fits the SMOK Nfix Pro Kit exclusively. It connects to the device via a gold-plated magnetic connection and accepts the full LP1 coil series for MTL vaping. The pod ships with no coil installed — you select and install the LP1 coil separately based on your preferred resistance and wattage. Among the pods and coils available in the UAE, this is the direct OEM replacement for the Nfix Pro system. Each pack contains 3 pods.

Which LP1 Coil Works in the Nfix Pro Pod and Why the Choice Matters

The Nfix Pro pod accepts the entire LP1 coil range. All four LP1 variants are built for MTL vaping, but each sits at a different resistance and wattage point, which changes the draw tightness, vapour temperature, and e-liquid consumption rate.

The 1.2ohm coil gives the tightest draw and suits users switching from cigarettes or those who use high-strength nicotine salts. The 0.8ohm meshed coil runs warmer and produces more vapour per puff while staying in the MTL range. The DC 0.8ohm dual coil covers a wider wattage range and gives slightly more flexibility on devices with adjustable output.

None of these coils are included in the pod pack. They are sold separately.

How the Side-Fill System and Adjustable Airflow Work Together

The Nfix Pro pod fills from the side via a silicone stopper. Pull the stopper back to expose the fill port, insert your bottle tip, fill to just below the 2ml maximum line, and press the stopper back flush. The silicone creates a leak-resistant seal at the fill point.

The base of the pod uses a leak-proof coil connection with silicone rings around the LP1 coil seat, which prevents e-liquid from reaching the airflow channel during normal use.

The pod also has an adjustable airflow slider. This lets you tighten or open the draw independently of the coil resistance you choose. A 0.9ohm coil with open airflow gives a different experience than the same coil with the airflow closed down. Combined with four coil resistance options, this gives you a wide range of MTL draw styles from a single pod format.

How to Install an LP1 Coil Into the Nfix Pro Pod

1. Remove the Nfix Pro pod from the device by pulling it free of the magnetic connection.
2. Press the LP1 coil into the base of the pod until it seats firmly. The coil clicks into place.
3. Fill the pod through the side-fill port. Replace the silicone stopper firmly after filling.
4. Let the filled pod sit upright for 5 minutes before use. This allows the e-liquid to saturate the coil cotton fully and prevents dry hits on the first puff.
5. Reattach the pod to the Nfix Pro device and start at the lower end of the coil’s recommended wattage.

Full Specifications

Frequently Asked Questions

Do coils come included with this pod pack?

No. The Nfix Pro Empty Pod Cartridge ships without coils. LP1 series coils are sold separately. You need to purchase and install an LP1 coil before the pod can be used.

Can I use this pod with any SMOK device other than the Nfix Pro?

No. The Nfix Pro pod uses a gold-plated magnetic connection specific to the Nfix Pro Kit. It does not fit other SMOK devices including those that use RPM, RPM 2, or Nord pod systems.

Which LP1 coil should I choose if I am switching from cigarettes?

The 1.2ohm meshed coil at 10 to 15W gives the tightest draw and most closely replicates the feel of a cigarette. Pair it with a nicotine salt e-liquid at 20mg or above for the most cigarette-like experience.

How long does one pod last before it needs replacing?

The pod body itself lasts several weeks with regular use. You replace the LP1 coil inside it every one to two weeks depending on how heavily you vape and the VG content of your e-liquid. Replace the pod when the body shows visible discolouration, cracking, or when the silicone stopper no longer seals properly.

What e-liquid ratio works best in the Nfix Pro pod?

All LP1 coils are built for MTL vaping. A 50/50 VG/PG ratio wicks cleanly at the low wattages these coils run at. High VG blends above 60% are too thick for the coil cotton to absorb fast enough between puffs and cause dry hits.