Smok RPM 2 DC MTL 0.6ohm Coil (5 Pack)

Stock up on SMOK RPM 2 DC MTL 0.6ohm Coils in UAE — 5 Pack

SMOK RPM 2 DC MTL 0.6ohm Coil is a dual-coil replacement for the RPM 2 pod system, available now at VapBuzz with fast delivery across UAE. It runs at 12 to 25W, with 20W being the practical sweet spot for most users. The DC in the name stands for dual coil — two wire coils wound together inside a single head rather than a single strand or mesh sheet. This gives a tighter, more controlled draw than the 0.16ohm mesh coil in the same RPM 2 range. Each pack contains 5 coils.

Installation is press-fit. You push the coil into the base of the RPM 2 pod until it clicks into place. No threading, no tools.

Why the 0.6ohm Dual Coil Produces a Tighter Draw Than Other RPM 2 Options

The RPM 2 coil range covers three resistance options, and each one produces a meaningfully different vaping experience. Understanding where the 0.6ohm DC MTL sits in that range helps you confirm you are ordering the right one.

The 0.6ohm coil runs at the lowest wattage of the three and produces the tightest draw. Higher resistance means the coil heats more slowly and draws less power per puff. The result is a cooler, tighter inhale that closely resembles the draw of a cigarette — which is why this coil is the standard recommendation for smokers switching to vaping.

At 12 to 25W, the vapour volume is lower than the mesh or 0.25ohm DC options. That is intentional for MTL use. A tighter draw with less vapour per puff delivers nicotine more efficiently when paired with salts or high-strength freebase, because the user inhales more frequently rather than taking larger draws.

Which SMOK Devices Are Compatible With the RPM 2 DC MTL 0.6ohm Coil

This coil fits any SMOK device that uses the RPM 2 pod. The RPM 2 pod is identified by the label on the e-liquid flap of the device. If it says RPM 2, this coil fits. If it says RPM (without the 2), it does not — RPM and RPM 2 coils are not interchangeable despite looking similar.

Confirmed compatible devices:

The coil itself is the same across all these devices. The pod it slots into varies by device. Always confirm you have the correct RPM 2 pod for your specific kit before ordering.

How to Install and Prime the 0.6ohm DC MTL Coil Correctly

Skipping the priming step is the most common reason new coils burn out within the first session. The cotton inside the coil needs to be saturated before you fire the device.

1. Remove the RPM 2 pod from your device and take out the old coil by pulling it free from the base.
2. Press the new 0.6ohm DC MTL coil into the pod base until it seats firmly. You should feel it click into place.
3. Fill the pod with e-liquid through the side-fill port and replace the silicone stopper.
4. Wait 5 to 10 minutes with the filled pod sitting upright. This allows the e-liquid to wick fully into the cotton inside the coil.
5. Reattach the pod to the device and start at the lower end of the wattage range — 12 to 15W. Take a few short puffs before moving up to your preferred wattage.

Running the coil at 25W without priming will burn the cotton in the first few puffs, producing a harsh burnt taste that does not go away. A replacement is then needed immediately.

E-Liquid Compatibility: Why 50/50 and Nicotine Salts Work Best at 0.6ohm

The 0.6ohm DC MTL coil runs at low wattage and produces low heat. High VG e-liquids — anything above 60% VG — are too thick to wick properly through the cotton at this wattage. They move slowly, the cotton does not saturate fast enough between puffs, and dry hits occur.

A 50/50 VG/PG ratio wicks cleanly at 12 to 25W and is the standard recommendation for this coil. Nicotine salts, which are typically formulated at 50/50 or higher PG ratios, work well here. The tight MTL draw and efficient nicotine delivery of salts complement each other at this resistance.

Freebase nicotine at 50/50 also works at concentrations of 6mg to 18mg. Above 18mg freebase, the throat hit at even 20W can become sharp. If you want high nicotine strength, salts are the more comfortable option at this coil resistance.

For other coil and pod options across different devices, the coils for vape section lists replacements sorted by brand and compatibility.

Full Specifications

Frequently Asked Questions

What is the difference between the RPM 2 DC MTL 0.6ohm and the RPM 2 Mesh 0.16ohm coil?

The 0.6ohm DC MTL is for tight, cigarette-like mouth-to-lung draws at 12 to 25W. The 0.16ohm mesh is for open, direct-to-lung vaping at 25 to 50W with high VG e-liquids. They are built for opposite vaping styles and are not interchangeable in terms of experience.

Will these coils fit my SMOK RPM (original) device?

No. RPM and RPM 2 coils are not interchangeable. The RPM 2 DC MTL 0.6ohm coil fits only devices that use the RPM 2 pod. Check the label on the e-liquid flap of your device — if it says RPM 2, this coil fits. If it says RPM only, it does not.

How long does one 0.6ohm DC MTL coil last?

With regular daily use and 50/50 e-liquid, most users get one to two weeks from each coil. Sweeter e-liquids with high sugar content caramelise on the coil faster and shorten lifespan. Chain vaping also reduces longevity significantly.

Can I use nicotine salts at 25mg or 50mg with this coil?

Yes. The 0.6ohm MTL coil at 12 to 25W is well-suited for nicotine salts at both concentrations. The tight draw and lower vapour volume make high-strength salts comfortable to use without harshness.

Why am I getting a burnt taste from a new coil?

Almost always a priming issue. The cotton was not fully saturated before the first puff. Once the cotton burns, the taste does not recover on that coil. Fill the pod, wait 5 to 10 minutes, and start at low wattage on every new coil going forward.